Amazone Cirrus 3002 Скачать руководство пользователя страница 76

Страница: 76 / 209

Structure and function

5.9.1

Connecting the blower fan to the tractor hydraulics

The blower fan speed alters until the hydraulic fluid has reached its

working temperature.
On initial operation correct the blower fan speed up to attainment of

the working temperature.
If the blower fan is put back into operation after a long stoppage

period, the preset blower fan speed is not attained until the hydrau-

lic fluid has heated up to working temperature.

The required blower fan speed can be found in the table (Fig. 71,

unterhalb). The blower fan speed depends on the machine working

width and on the seed.

The blower fan speed can be regulated:

•

at the tractor flow control valve

or (if not present)

•

via the pressure relief valve (Fig. 70/3) of the hydraulic motor.

The blower fan speed (rpm) is dependent on

•

the working width of the machine (1).

•

the seed

fine seeds (2),

e.g. rape or grass seed

grain and

pulses (3).

Example:

Cirrus 4002

•

Working width 4.0 m (1)

•

Cereal seed (3)

Required blower fan speed: 3800 rpm

Fig. 71

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды