Amazone Cirrus 3002 Скачать руководство пользователя страница 21

Страница: 21 / 209

General Safety Instructions

MD080

Risk of contusions to torso in the bend area
of the drawbar due to sudden steering
movements!

This danger will cause serious injuries to the

torso or death.
It is forbidden to stand in the danger area be-

tween the tractor and the machine for as long as

the tractor engine is running and the tractor is

unprotected against unintentional rolling.

MD081

Danger of getting crushed for the whole body
by machine parts that are raised by lifting
cylinders and unintentionally lowered!

This danger will cause serious injuries anywhere

on the body or death.
Secure the machine parts raised by the lifting

cylinder against unintentional lowering before

you enter the danger zone under raised machine

parts.
To do so, use the mechanical lifting cylinder

support or the hydraulic blocking device.

MD082

Danger of falling from treads and platforms
when riding on the machine!

This danger will cause serious injuries anywhere

on the body or death.
It is forbidden to ride on the machine and/or

climb the running machine. This ban also applies

to machines with treads or platforms.
Ensure that no-one rides with the machine.

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды