Amazone Cirrus 3002 Скачать руководство пользователя страница 17

Страница: 17 / 209

General Safety Instructions

2.10

Constructive changes

You may make no changes, expansions or modifications to the ma-

chine without the authorisation of AMAZONEN-WERKE. This is also

valid when welding support parts.
Any expansion or modification work shall require the written approval

of AMAZONEN-WERKE. Only use the modification and accessory

parts released by AMAZONEN-WERKE so that the operating permit,

for example, remains valid in accordance with national and interna-

tional regulations.
Vehicles with an official type approval or with equipment connected to

a vehicle with a valid type approval or approval for road transport

according to the German road traffic regulations must be in the state

specified by the approval.

WARNING

Risk of contusions, cuts, dragging, catching or knocks from
support parts.

It is forbidden to:

•

Drill holes in the frame or on the running gear.

•

Increasing the size of existing holes on the frame or the running

gear.

•

Welding support parts.

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды