Amazone Cirrus 3002 Скачать руководство пользователя страница 34

Страница: 34 / 209

General Safety Instructions

the approved axle and support loads of the tractor.

•

The tractor must guarantee the prescribed brake delay for the

loaded vehicle combination (tractor plus connected machine).

•

Check the brake power before moving off.

•

When turning corners with the machine connected, take the

broad load and balance weight of the machine into account.

•

Before moving off, ensure sufficient side locking of the tractor

lower links, when the machine is fixed to the three-point hydrau-

lic system or lower links of the tractor.

•

Before moving off, move all the swivel machine parts to the

transport position.

•

Before moving off, secure all the swivel machine parts in the

transport position against risky position changes. Use the

transport locks intended for this.

•

Before moving off, secure the operating lever of the three-point

hydraulic system against unintentional raising or lowering of the

connected machine.

•

Check that the transport equipment, e.g. lighting, warning

equipment and protective equipment, is correctly mounted on the

machine.

•

Before transportation, carry out a visual check that the upper and

lower link bolts are firmly fixed with the lynch pin against uninten-

tional release.

•

Adjust your driving speed to the prevailing conditions.

•

Before driving downhill, switch to a low gear.

•

Before moving off, always switch off the independent wheel

braking (lock the pedals).

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды