Amazone Cirrus 3002 Скачать руководство пользователя страница 57

Страница: 57 / 209

Product description

Hydraulic system

Maximum operating pressure: 210 bar
Tractor pump power:

At least 80 l/min at 150 bar

Machine hydraulic fluid:

Transmission/hydraulic fluid Utto SAE 80W API GL4
The machine hydraulic/transmission fluid is suitable for the combined

hydraulic/transmission fluid circuits of all standard makes of tractor.

Control unit

yellow

Double-acting control unit

Control unit

green

Double-acting control unit

Control unit

red

•

1 single-acting or double-acting control unit with priority control

for the feed line

•

1 unpressurised return line with a large push-fit coupling (ND 16)

for the unpressurised oil return line. In the return line the bank-

ing-up pressure must be 10 bar at the maximum.

Operational brake system

•

Dual-circuit service brak-

ing system:

•

1 hose coupling (red) for the supply line

•

1 hose coupling (yellow) for the brake line

•

Hydraulic

braking system:

1 hydraulic coupling in accordance with ISO 5676

The hydraulic braking system is not allowed in Germany and several

other EU countries!

4.10

Noise production data

The workplace-related emission value (acoustic pressure level) is 74

dB(A), measured in operating condition at the ear of the tractor driver

with the cabin closed.
Measuring unit: OPTAC SLM 5.
The noise level is primarily dependent on the vehicle used.

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды