Amazone Cirrus 3002 Скачать руководство пользователя страница 109

Страница: 109 / 209

Coupling and uncoupling the machine

7.1.2

Connecting the electrical connections

Connection/function

Installation information

Plug (7-pin) for the road traffic lighting system

AMATRON 3 machine plug

Connect the plugs to the terminal as described in

the AMATRON 3 operating manual.

7.1.3

Connecting the pneumatic service brake system

Tractor connection

Function

Connection

Marking

Brake line

Yellow

Pneumatic braking system

Supply line

Red

Couple to the tractor

•

first of all the yellow hose coupling (brake line)

•

then the red hose coupling (supply line).

Make sure that they engage correctly!
The brake is released immediately from braked position (braked posi-

tion possible only if the compressed air tank is full) when the red hose

coupling is coupled.
Before coupling the brake line or supply line ensure that the

•

hose couplings are clean

•

the sealing rings of the hose couplings are in perfect condition

•

the seals are clean and undamaged.

Cirrus BAH0049-1 09.14

109

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды