Amazone Cirrus 3002 Скачать руководство пользователя страница 140

Страница: 140 / 209

Transportation

When driving on public roads and ways the tractor and machine

must comply with the national road traffic regulations (in Germany

the StVZO and the StVO) and the accident prevention regulations (in

Germany those of the industrial injury mutual insurance organisa-

tion).
The vehicle keeper and driver are responsible for compliance with

the statutory stipulations.
Furthermore, the instructions in this section have to be complied with

prior to starting and during travel.

•

For transport journeys take heed of the section "Safety infor-

mation for users", Seite 31.

•

Before moving off, check:

The correct connection of the supply lines

The lighting system for damage, function and cleanliness

The brake and hydraulic system for visible damage

The function of the brake system.

WARNING

Risk of contusions, cutting, catching, drawing in and knocks
when making interventions in the machine through unintentional
machine movements.

•

On folding machines, check that the transport locks are locked

correctly.

•

Secure the machine against unintentional movements before

starting transportation.

WARNING

Risk of contusions, cuts, dragging, catching or knocks from
tipping and insufficient stability.

•

Drive in such a way that you always have full control over the

tractor with the attached machine.

In so doing, take your personal abilities into account, as well as

the road, traffic, visibility and weather conditions, the driving

characteristics of the tractor and the connected machine.

•

Before transportation, fasten the side locking of the tractor lower

link, so that the connected or coupled machine cannot swing

back and forth.

140

Cirrus BAH0049-1 09.14

Содержание Cirrus 3002


















































































































































































































Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cirrus 3002, Руководство по эксплуатации

Результаты поиска

Содержание Cirrus 3002

Отзывы:

Бренды по названию

Популярные бренды