ABB FCAN-01 Скачать руководство пользователя

Страница: 106 / 176

106 Communication profiles



References

References are 16-bit signed two's complement integers. A

negative reference indicates a reverse direction of rotation.
ABB drives can receive control information from multiple sources

including analogue and digital inputs, the drive control panel and a

communication module (for example, FCAN-01). To have the drive

controlled through the fieldbus, the module must be defined as the

source for control information, for example, reference.

Scaling

References are scaled as shown below.

Note:

The values of REF1 MAX and REF2 MAX are set with drive

parameters. See the drive manuals for further information.
In ACSM1, ACS850 and ACS880 the speed reference (REFx) in

decimal (0…20000) corresponds to 0…100% of the speed scaling

value (as defined with drive parameter, eg, ACS850 parameter

19.01 Speed scaling

, ACS880 parameter

46.01 Speed scaling

In ACS355, drive parameter REFx MIN may limit the actual

minimum reference.

Fieldbus

Drive

REF2: 10000
REF1: 20000

REF2: -10000
REF1: -20000

REFx MAX / Speed scale

REFx MIN

-(REFx MIN)

-(REFx MAX) / Speed scale

Содержание FCAN-01

















































































































































































Результаты поиска

Содержание FCAN-01

Отзывы:

Похожие инструкции для FCAN-01

Бренды по названию

Популярные бренды

ABB FCAN-01, Руководство пользователя

Результаты поиска

Содержание FCAN-01

Отзывы:

Похожие инструкции для FCAN-01

Бренды по названию

Популярные бренды