ABB FCAN-01 Скачать руководство пользователя

Страница: 115 / 176

Communication protocol 115

Tx PDO1

Note:

The mapping entries of the Tx PDO1 can be configured

through CANopen object 1A00h or from the drive with fieldbus

configuration parameter group C (group 3).
The default COB ID for Tx PDO1 is 180h + Node ID, the default

transmission type is 255 and the event time is 0. These values can

be changed with CANopen object 1600h or from the drive with

parameters 10, 11 and 12 of the fieldbus configuration group A

(group 1).

Mapped

obj 1

Mapped

obj 2

Mapped

obj 3

Mapped

obj 4

Byte

CANopen object for

mapping

1A00h01

1A00h02

1A00h03

1A00h04

Mapping

parameter

ACS355

Fixed

FBA
DATA IN 1

FBA
DATA IN 2

FBA
DATA IN 3

ACSM1

ACS850
ACS880

FBA
DATA IN 1

FBA
DATA IN 2

FBA
DATA IN 3

FBA
DATA IN 4

In ACS355 drives, the first mapping entry is fixed and always mapped to object

6041h Status word. The other mapping entries are configurable. In ACSM1,
ACS850 and ACS880 drives, all mapping entries are configurable.

Configuration group C (group 3) (when parameter 04 CONF LOC = 1)

Содержание FCAN-01

















































































































































































Результаты поиска

Содержание FCAN-01

Отзывы:

Похожие инструкции для FCAN-01

Бренды по названию

Популярные бренды

ABB FCAN-01, Руководство пользователя

Результаты поиска

Содержание FCAN-01

Отзывы:

Похожие инструкции для FCAN-01

Бренды по названию

Популярные бренды