manualshive.com logo in svg

ABB FCAN-01, Руководство пользователя

Поделиться
Скачать
ABB FCAN-01 Скачать руководство пользователя страница 24

24  Overview of the CANopen protocol and the FCAN-01 adapter module        

The physical medium of CANopen is a differentially driven two wire 

bus line with common return according to ISO 11898. The 

maximum length of the bus is limited by the communication speed.
The maximum theoretical number of nodes is 127. However, in 

practice, the maximum number depends on the capabilities of the 

used CAN transceivers.
Further information is available from the CAN in Automation 

International Users and Manufacturers Group (

www.can-cia.org

).

Topology of the CANopen link

The figure below shows an example topology of the CANopen link.

CANopen 

master

ABB drive

Other slave 

device

T = Termination

T

ABB drive

ABB drive

Other slave 

device

Other slave 

device

T

ABB drive

Содержание FCAN-01

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды