manualshive.com logo in svg

ABB FCAN-01, Руководство пользователя

Поделиться
Скачать
ABB FCAN-01 Скачать руководство пользователя страница 89

Communication profiles   89

CANopen device profile CiA 402

Device Control state machine

The start and stop of the drive and several mode-specific 

commands are executed by the Device Control state machine. 

This is described in figure below.

The Control word is the principal means for controlling the drive 

from a fieldbus system. It is sent by the fieldbus master station to 

the drive through the adapter module. The drive switches between 

its states according to the bit-coded instructions in the Control 

word, and returns status information to the master in the Status 

word.
The contents of the Control word and the Status word are detailed 

section 

Control word and Status word of the CiA 402 profile

 on 

page 

93

.

Homing 

mode

Profile 

Position 

mode

Inter-

polated 

Position 

mode

2)

Profile 

Velocity 

mode

Profile 

Torque 

mode

Velocity 

mode

2)

 Not supported

1)

 ACS355 supports only vl.

1)

 ACS850 and ACS880 support vl and tq.

1)

 ACSM1 supports hm, pp, pv, tq and vl.

Device Control state machine

Modes of operation

1)

Содержание FCAN-01

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды