A&D AD-4410 Скачать руководство пользователя страница 8

Страница: 8 / 82

AD-4410

Page

3.3. General

3.3.1. Interface

Control I/O

Input: open collector Output: photo coupler
DIN connector 8 pin

Standard serial output

Output for communication with A&D peripheral devices
(20 mA current loop) DIN connector 7 pin

RS-232C
(Standard equipment)

D-sub 9 pin male

RS-232C/RS-485 (Option)

It is possible to change the current loop to the RS-232C
(ch2) or RS-485.
RS-232C AD4410-04
RS-485 AD4410-03

3.3.2. Measuring functions

Zero adjustment

•

Sets the gross weight to zero by pressing the ZERO key.

•

Selection of disable or enable for the operation when unstable.

•

The zero value is stored in the non-volatile memory.

•

Zero adjustable range

Can be set optionally in the range of 1 to 100% of the

weighing capacity.

Zero tracking

•

Tracks the weight drift around the zero point to maintain zero.

•

Zero tracking time

0.0 to 5.0 seconds (Can be set optionally within the range.)

•

Zero tracking band

0.0 to 9.9 d (Can be set optionally within the range.)

Tare

•

Sets the net weight to zero by pressing the TARE key.

•

Selection of disable or enable for the operation when

unstable or negative.

•

The tare weight is stored in the non-volatile memory.

•

Tare range: Gross weight

≤

Weighing capacity

Stability detection

•

Turns ON the stabilization indicator when the variables of

the weight values per sampling are within the set band in
the set time.

•

Stability detection time

0.0 to 9.9 seconds (Can be set optionally within the range.)

•

Stability detection band

0 to 9 d (Can be set optionally within the range.)

Digital filter

Cutoff frequency range (-3dB) : 0.07 to 11 Hz

Near zero detection function

Detects whether there is a load or not and outputs the result
as near zero.

Comparison function

HI, OK, or LO is output by comparing a value to an upper or
lower limit value.

Hold function

This is displayed by holding the weighing value.
Normal hold / Peak hold / Averaging hold

Содержание AD-4410



















































































Результаты поиска

Содержание AD-4410

Отзывы:

A&D AD-4410, Инструкция по эксплуатации, Страница: 8 / 82

Результаты поиска

Содержание AD-4410

Отзывы: