A&D AD-4410 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 82

A&D AD-4410 Скачать руководство пользователя страница 56

AD-4410

Page

54

9.2.5. Bit structure

Data 7 bits

Data 8 bits

9.2.6. Data transfer mode

Four data transfer modes are available; stream, auto printing, manual printing or jet
stream.

Stream mode

Transmits data in sync with the display update rate. If
the indicator can not catch up with the update rate
because of the baud rate, the transmission is paused
until the next updating.
The transmitted data is the same as what is being
displayed. Data that is not displayed is never
transmitted.

Auto printing mode

Transmits data one time once a weight value of 5 d or
greater has stabilized.
For a further transmission, the weight value must fall
below 5 d and then stabilize again above that value.

Manual printing mode

Transmits data when the F key, assigned as the
manual print command, is pressed.

Jet stream

Transmits data in sync with the sampling rate. If the
indicator can not catch up with the sampling because
of the baud rate, the transmission is paused until the
next sampling.

Functions related to the data transfer mode

z

Set

Cl f04

,

r51f06

or

r52f06

(ID number) to add an ID number to standard serial

output.

Example:

z

Set

Calf20

(disables negative output)

to disable the print command when gross

weight is negative.

z

Set

Calf22

(header 2)

to change header 2 to G, N or T.

S T , G S , + 0 1 2 3 . 4 5 k g

CR LF

0 9

@

ID number

Stop bit

Stop bit

Start bit

Data bit

Data bit

Parity bit

«
...
54
55
56
57
58
...
»

Содержание AD-4410



















































































Отзывы:

Нет отзывов