A&D AD-4410 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 82

A&D AD-4410 Скачать руководство пользователя страница 26

AD-4410

Page

24

7.2. Calibration With an Actual Load (

Cal5et

)

Calibration is performed using a calibration weight
Before performing calibration for the first time, set the unit, decimal point position,
minimum division and weighing capacity in the calibration-related function mode.

NOTE: To avoid drift caused by changes in temperature, warm up the indicator for

ten minutes or more before performing calibration with an actual load.

Step 1 Press the ON/OFF key to turn the indicator ON

(weighing mode) if it is in the OFF mode.
Remove the CAL key cover and press the CAL
key.

CalL

is displayed to indicate that the indicator

has entered the calibration mode.

Step 2 Press the ENTER key to display

Cal5et

.

The indicator enters the mode of calibration with
an actual load. To go back to the weighing mode,
press the ESC key.

Zero calibration

Step 3 Press the ENTER key to display

Cal 0

.

If zero calibration is not to be performed, press
the F key and go to step 5.
To monitor the current weight value, press the
CAL key. Press the CAL key again to display

CalL 0

.

Step 4 With nothing placed on the load cell, wait for the

stabilization indicator to turn ON and press the
ENTER key. - - - - - - is displayed for
approximately two seconds.
If span calibration is not to be performed, press
the ESC key twice to return to the weighing
mode.

Span calibration

Step 5 Press the ENTER key when

Cal5pn

is

displayed.
The calibration weight value (the weighing
capacity currently set) is displayed and the
lowest value number blinks.

«
...
24
25
26
27
28
...
»

Содержание AD-4410



















































































Отзывы:

Нет отзывов