A&D AD-4410 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 82

A&D AD-4410 Скачать руководство пользователя страница 44

AD-4410

Page

42

Step 6 Press the ESC key. The function number disappears and the indicator returns to

the state of step 3.
Press the ESC key to store the setting values in the FRAM and go back to the
weighing mode.

NOTE: The blinking decimal point indicates that the current value is not the weight

value.

If a value exceeding the settable range is entered,

err dt

is displayed and

the input is canceled.

8.2. Adjusting the digital filter

Adjust the digital filter using

fncf05

(digital filter).

The available settable range for the cutoff frequency is from 11 Hz to 0.07 Hz.
The cut off frequency is the frequency where vibrations begin to decline.

1. If the weighing value is unstable, set the cutoff frequency lower.

2. To make the response faster, set the cutoff frequency higher.

Cut off frequency is high.
Response rate is fast.
Weak against disturbances.

Cut off frequency is low.
Response rate is slow.
Strong against disturbances.

* It is possible to make adjustments while watching the effects of the digital filter with your own

eyes.

By pressing the CAL key while setting

fncf05

(digital filter), it is possible to check the

weight displayed.

ZERO key Set the display to zero.

∧

Key Increase stability.

∨

Key Increase speed.

CAL key Return to the value setting display.

«
...
42
43
44
45
46
...
»

Содержание AD-4410



















































































Отзывы:

Нет отзывов