ZIEHL-ABEGG ZETADYN 3C Page 146 Original Operating Instructions Download

Page: 146 / 204

Error no.

Error text

Error cause

M S

830

CAN: Timeout Enab.-

Det.

Error:

Control system gives command "Enable Operation" not within T_CMD

Adjustment:

Increase time for T_CMD

831

CAN: Timeout Dis. Op.

Error:

Control system gives command "Disable Operation" not within T_CMD

Adjustment:

Increase time for T_CMD

832

CAN: Timeout Shut-

down

Error:

Control system gives command "Shutdown" not within T_CMD. Occurs by
closing the brakes.

Adjustment:

Increase time for T_CMD

833

CAN: Timeout Dis. Vol.

Error:

Control system gives command "Disable Voltage" not within T_CMD. Occurs at
end of travel.

Adjustment:

Increase time for T_CMD

840

CAN: ENC. Info missing

Error:

The object "Encoder Info" was not written to the frequency inverter by the
control system

13.5.11

Error 9xx

•

Fatal error, which can only be acknowledged by switching off the frequency inverter

Error no.

Error text

Error cause

M S

905

MOP:HW-SW Error

Error:

A hard- or software error occured after switching on the inverter. After

60s the inverter chabges to "Wait-Switch off"

Remedy:

Check the connectors between the Control Unit and Modul Print

check the fuse on the Switching Power Print
no Modul Print existing
check EEprom on the Modul Print

906

ZR_ERR by start

Error:

No signal at BC input during ZETADYN start-up

Remedy:

Check wiring

Use the ZArec display to check for an error at the ZArec

908

PFU: No function

Fault:

When switching on the converter, the monitor contact of the feedback

unit is not closed

Remedy:

Check connection of the feedback unit function monitor,

Check function monitor of power feedback unit,
Check

ﬁ

eld of rotation of the mains connection for the power feedback unit

●

910

BC: No function

Error:

When switching on the inverter, the monitoring contact for the Brake-

Chopper or Brake resistor is not closed

Remedy:

Check the temperature monitor for the Brake-Chopper or Brake

resistor,
check the temperature monitoring for the Brake-Chopper or Brake-Resistor,

911

BRxx: Overload

Error:

The continious braking power of the Brake resistor is exceeded by

150 % within 120 s
The inverter switches off during the travel

Remedy:

Check the con

ﬁ

guration of the BR-type

Check the connected BR

●

912

BC: Fault

Error:

Monitoring contact for Brake-Chopper or Brake resistor opens while the

inverter is operating

Remedy:

Check the temperature monitor for the Brake-Chopper or Brake

resistor,
check the temperature monitoring for the Brake-Chopper or Brake-Resistor,

Original operating instructions

ZETADYN 3C

Error diagnosis

R-TBA08_03-GB 1619

Part.-No. 00163322-GB

146/204

Summary of Contents for ZETADYN 3C













































































































































































































Search results

Summary of Contents for ZETADYN 3C

Reviews:

Related manuals for ZETADYN 3C

Brands by name

Popular brands

ZIEHL-ABEGG ZETADYN 3C, Original Operating Instructions

Search results

Summary of Contents for ZETADYN 3C

Reviews:

Related manuals for ZETADYN 3C

Brands by name

Popular brands