YOKOGAWA AQ7280 OTDR User Manual Download Page 80

Page: 80 / 195

2-55

IM AQ7280-01EN

Optical Pulse Measurement (OTDR)

Index

For details on how to operate the OPM module and VLS module, see the following sections.

• Optical power meter: Section 5.2

• Power checker: Section 5.2

• Light source, visible light source: Section 5.1

• Fiber end face inspection probe: Section 8.6

Changing the Scale

You can set the waveform amplitude span and the distance axis.

Switch the menu display.

Tap to switch the menu display.

Set the display range.

Flick to scroll the menu.

• Switching the Menu Display

You can switch the menu display as follows.

: The menu is displayed in a tabular form.

: The menu is displayed in a scrollable form.

Scrollable form

Tabular form

2.10 Using Convenient Touch Operation Features

Summary of Contents for AQ7280 OTDR




































































































































































































Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands

YOKOGAWA AQ7280 OTDR, User Manual

Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands