YOKOGAWA AQ7280 OTDR User Manual Download Page 63

Page: 63 / 195

2-38

IM AQ7280-01EN

Main View Screen

From the top menu, select

Multi Fiber Project

to display the following screen.

Using the arrow keys or the rotary knob, move the

cursor to the cell of a core number you want to measure.

Saved result indication

Blue: Measured data saved

Green: Measured data saved, pass judgment

Red: Measured data saved, pass judgment

Observation data of the fiber end face already saved

Measured data of optical power already saved

Core number

Create a new project.
Project information

Displays project information

Set the wavelength.

You can select one of the

wavelengths that have been

set in the measurement

conditions or "All."

Clear the check mark.

Clears the result indication

in the cell at the cursor

location and deletes the

saved data.

Specifies skip

You can skip cores you do not want to measure. You can select this soft key

when the cell at the cursor location does not have a result indication. To cancel

skipping, press this soft key again.

Core numbers set to Skip are not displayed.

The number of cores whose measurement results have been saved

The drive/folder name/project name of the current project

Confirm the waveform.

You can confirm the

measurement waveform.

You can change the marker

and event positions.

Preview area

Information about the core

number at the cursor location

The cell of the core number of the

next project (96 core/100 core)

The cell of the core number of the previous project (96 core/100 core)

Switches between file name and label display

Tap the icon to switch between displaying the waveform file

name and label information of the measured core.

Using the

arrow keys

or the

rotary knob

, move the cursor to the cell of a core number you

want to measure.

Note

To measure the optical power and observe the fiber end face, tap a core No.

Realtime

Performs real-time measurement. Operates in the same manner as the REALTIME key.

Optical power measurement

(see section 5.2)

Average

Performs averaged measurement. Operates in the same manner as the AVG key.

Fiber inspection probe

Observe the fiber end face. See section 8.6.

2.8 Performing Multi-Core Fiber Measurement

Summary of Contents for AQ7280 OTDR




































































































































































































Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands

YOKOGAWA AQ7280 OTDR, User Manual

Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands