manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

1-1

IM AQ7280-01EN

Features

1

2

3

4

5

6

7

8

Index

1.1 Overview

System Configuration

The AQ7280 consists of a mainframe and OTDR unit. If necessary, an OPM module can be installed 
into the mainframe to measure loss in optical fiber cables and view the power of communication light. 
An VLS module can be installed to visually check the fault location.

OTDR unit

Control and computation block

Internal

memory

SD card

PC

TypeA x2

SD slot

ETHERNET

(/LAN option)

USB (TypeB_mini)

Power 

supply block

Battery 

pack

AC adapter

Mainframe

Visible light (CW, CHOP)

Measurement light (CW, CHOP)

Visible light (with the visible light source 

feature; CW, CHOP)

Optical pulse: OTDR

Measurement light: Light source (/SLS)

 

Power checker (/PC)

OPM module

VLS module

Control 

block

Display 

block

USB memory,

fiber inspection 

probe, printer

Mainframe

  The AQ7280OTDR mainframe. In combination with an OTDR unit, the mainframe can test for 

breaks, connections, losses, and the like. In addition, by installing an option module, you can use 
the mainframe as an optical power meter or visible light source.

  The main processes performed on the mainframe are as follows:

•  Key and touch panel operations
•  Set measurement conditions
•  8.4 inch large LCD
•  Multi touch support
•  Battery driven
•  System that enables both units and modules to be controlled
•  Remote control through external interfaces (USB, Ethernet (/LAN option))

  The mainframe runs on an AC adapter (sold separately) or internal battery. The AC adapter (sold 

separately) is required to charge the internal battery.

Chapter 1 

Features

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Nagano Keiki GC31 Instruction Manual preview
GC31
Brand: Nagano Keiki Pages: 25
S.E. International USB Inspector Operation Manual preview
USB Inspector
Brand: S.E. International Pages: 30
SZBJ BM5263 Operator'S Manual preview
BM5263
Brand: SZBJ Pages: 2
PHYWE Cobra SMARTsense Ammonium Ion 12913-00 Operating Instructions preview
Cobra SMARTsense Ammonium Ion 12913-00
Brand: PHYWE Pages: 5
Halo Photonics Stream Line Pro Hardware And Software Manual preview
Stream Line Pro
Brand: Halo Photonics Pages: 45
Dive Perfect Stubby LED-1500 User Manual preview
Stubby LED-1500
Brand: Dive Perfect Pages: 4
MRC PVB-820 Operation Manual preview
PVB-820
Brand: MRC Pages: 14
Tonghui TH2689 Operation Manual preview
TH2689
Brand: Tonghui Pages: 65
Fisso Photo Set Strato S-20 Instructions For Use preview
Photo Set Strato S-20
Brand: Fisso Pages: 2
PCB Piezotronics IMI Sensors 66212ANZ2 Installation And Operating Manual preview
IMI Sensors 66212ANZ2
Brand: PCB Piezotronics Pages: 6
Voweek VGR2106 Operation Manual preview
VGR2106
Brand: Voweek Pages: 20
T&D TR-76Ui Getting Started Manual preview
TR-76Ui
Brand: T&D Pages: 2
Waters Xevo TQ-XS Mass Overview And Maintenance Manual preview
Xevo TQ-XS Mass
Brand: Waters Pages: 213
Keysight E8740A-020 Startup Manual preview
E8740A-020
Brand: Keysight Pages: 41
Hesai 4498 Technical Documentation Manual preview
4498
Brand: Hesai Pages: 8
Badger Meter Recordall Disc Series Installation Manual preview
Recordall Disc Series
Brand: Badger Meter Pages: 4
Apera Instruments SX751 User Manual preview
SX751
Brand: Apera Instruments Pages: 32
Thermal Gas Systems HALOGUARD II Instruction Manual preview
HALOGUARD II
Brand: Thermal Gas Systems Pages: 13

Brands by name

Popular brands

Load more brands