manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

8-12

IM AQ7280-01EN

Pass/Fail Judgment (/FST Option)

Judgment Results (Summary)

  Displays the judgment results and the number of detected scratches (Scratch) and detects (Defect). 

The detection count is displayed separately for the core, cladding, and contact areas.

  The judgment will be fail if there is even only a single fail (×) judgment.

  Judgment result display
 Pass: 

 V

 Fail:  X 

(red)

  

Judgment result

Number of detected scratches and defects

Judgment Results (Details)

  For each of the core, cladding, and contact areas, the threshold (Setting) and detection count (Result) 

are displayed.

  If the detection count (Result) exceeds the threshold (Setting), the judgment will be fail (×).
  Scratches and defects are detected separately by size.
 Example

  Scratch (<=3 um): Scratches less than or equal to 3 μm
  Scratch (>3 um): Scratches exceeding 3 μm
  Defect (2 to 5 um): Scratches between 2 μm and 5 μm

Configuring the Pass/Fail Judgment

•  Selecting the Optical Fiber Cable

  Select the type of optical fiber cable to be judged.
  SM: Single mode
  MM: Multi mode

•  Turning Judgment Execution On or Off

  Executes judgment of scratches and defects separately by size. The size value is fixed.
  Clearing the check box turns off the judgment execution. Pass/fail judgment is not performed on 

scratches and defects whose check box is not selected.

•  Setting the Scratch or Defect Judgment Threshold Values

  Set the number of scratches and defects that will be judged as fail. The range is 0 to 100.
  If the judgment execution check box explained above is cleared, No Limit is displayed.

•  Select the judgment reference.

  Select the ferrule’s polished surface of optical fiber cable to be judged.
  The judgment reference varies depending on the polished surface. When you select the 

polished surface, the judgment execution on/off and scratch or defect judgment threshold values 
explained above are set automatically.

  UPC, SPC:   For spherical surface polishing
  APC:       For angled spherical surface polishing
  User:        When judgment execution and threshold are set manually (when any of the settings 

is changed, the judgment reference is automatically set to User)

Saving Data

  The judgment result image and a judgment result file (including judgment settings) in CSV format 

are saved with the same file name (excluding the extension). Video cannot be saved.

8.6  Checking the Optical Fiber End Face for Stains

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Macherey-Nagel NANOCOLOR Advance Operating Instruction preview
NANOCOLOR Advance
Brand: Macherey-Nagel Pages: 45
Vaisala HUMICAP HMP155 Quick Manual preview
HUMICAP HMP155
Brand: Vaisala Pages: 2
Dräger Alcotest 7000 Instructions For Use Manual preview
Alcotest 7000
Brand: Dräger Pages: 538
ADA INSTRUMENTS A00108 Operating Manual preview
A00108
Brand: ADA INSTRUMENTS Pages: 27
Clavia Nord C1 Service Manual preview
Nord C1
Brand: Clavia Pages: 13
ICP DAS USA PM-3133-MTCP User Manual preview
PM-3133-MTCP
Brand: ICP DAS USA Pages: 71
CONDTROL xMarker User Manual preview
xMarker
Brand: CONDTROL Pages: 11
Milwaukee 2206-20 Repair Service Instructions preview
2206-20
Brand: Milwaukee Pages: 17
Feasa ICT Series User Manual preview
ICT Series
Brand: Feasa Pages: 145
Amrutha Technologies AlcoEasy A65 Operating Manual preview
AlcoEasy A65
Brand: Amrutha Technologies Pages: 22
Straightpoint LLP Operating Instructions Manual preview
LLP
Brand: Straightpoint Pages: 24
MSA AUER Atemluft 300 bar Operating Manual preview
AUER Atemluft 300 bar
Brand: MSA Pages: 52
THORLABS NR360S User Manual preview
NR360S
Brand: THORLABS Pages: 20
Gatekeeper Y35HD Quick Install Manual preview
Y35HD
Brand: Gatekeeper Pages: 2
Midtronics Celltron ULTRA Instruction Manual preview
Celltron ULTRA
Brand: Midtronics Pages: 58
GE SimpliNano Original Instructions Manual preview
SimpliNano
Brand: GE Pages: 16
Raycus A6000D User Manual preview
A6000D
Brand: Raycus Pages: 86
Environmental Express 35643-00 Instruction Manual preview
35643-00
Brand: Environmental Express Pages: 17

Brands by name

Popular brands

Load more brands