manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

2-1

IM AQ7280-01EN

Optical Pulse Measurement (OTDR)

1

2

3

4

5

6

7

8

Index

2.1  Setting the Measurement and Analysis 

Conditions

Setup Menu

1.

  From the top menu, select 

OTDR

.

2.

 Press 

SETUP

 to display the Setup menu.

 

  

Set the measurement mode (Simple, Detail, PON).

Set the measurement conditions.

Set the analysis conditions.

Configure the waveform display.

See section 3.2.

Configure the system.

See chapter 7.

Setting the Measurement Mode

Simple:   In Simple mode, you set only a portion of the measurement and analysis conditions 

(wavelength, approximation method, etc.), and the AQ7280 automatically detects and sets the 
rest of the measurement conditions related to measurement resolution—such distance range 
and pulse width—and analysis conditions related to the optical fiber cable—such as index of 
refraction and backscatter.

Detail:   In Detail mode, you set the measurement and analysis conditions individually. If you set 

the measurement conditions—such as the distance range and pulse width—to Auto, the 
AQ7280 will determine the suitable range and perform the measurement like in Simple Mode, 
described above.

PON:    In PON mode, the AQ7280 determines the suitable measurement and analysis conditions 

based on the number of optical splitter stages, route information, and distance range to set 
the optimal values. These values can be changed if necessary.

Note

When you change from Simple mode to Detail or PON mode, you may be asked to enter a password. This 
means that there are restrictions placed on operating the AQ7280. To change the measurement mode, 
you need to verify with the AQ7280 administrator. For details on operation restrictions, see “Operation 
Restrictions” in section 7.6.

Chapter 2 

Optical Pulse Measurement (OTDR)

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Cannon CAV 4.2 Operation Manual preview
CAV 4.2
Brand: Cannon Pages: 64
Cannon CAV 4.1 Operation Manual preview
CAV 4.1
Brand: Cannon Pages: 73
Keithley 485 Quick Reference Manual preview
485
Brand: Keithley Pages: 32
Gazelle G9407-Log Operating Instruction preview
G9407-Log
Brand: Gazelle Pages: 2
Narvitech NS110 Quick Manual preview
NS110
Brand: Narvitech Pages: 2
UE Systems Ultraprobe 9000 Manual preview
Ultraprobe 9000
Brand: UE Systems Pages: 25
UE Systems ULTRAPROBE 10000 General Setup And Knowledge preview
ULTRAPROBE 10000
Brand: UE Systems Pages: 6
Yamaha P-155 Bedienungsanleitung preview
P-155
Brand: Yamaha Pages: 72
Yamaha P-125a Midi Reference preview
P-125a
Brand: Yamaha Pages: 5
Yamaha P-125 Manual preview
P-125
Brand: Yamaha Pages: 16
Yamaha P-105 Reference preview
P-105
Brand: Yamaha Pages: 8
Yamaha Modus F02 Reference Manual preview
Modus F02
Brand: Yamaha Pages: 7
Yamaha J-5000 Owner'S Manual preview
J-5000
Brand: Yamaha Pages: 60
Yamaha GranTouch Digital Grand Piano Bedienungsanleitung preview
GranTouch Digital Grand Piano
Brand: Yamaha Pages: 19
Yamaha EZ-TP Manual De Instrucciones preview
EZ-TP
Brand: Yamaha Pages: 44
Yamaha Electone E-50 Manual preview
Electone E-50
Brand: Yamaha Pages: 29
Yamaha PDP-101 Manual De Instrucciones preview
PDP-101
Brand: Yamaha Pages: 47
ABB ProcessMaster FEP630 series Manual preview
ProcessMaster FEP630 series
Brand: ABB Pages: 92

Brands by name

Popular brands

Load more brands