manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

2-17

IM AQ7280-01EN

Optical Pulse Measurement (OTDR)

1

2

3

4

5

6

7

8

Index

2.3  Performing Averaged Measurement and 

Displaying the Results with Icons (/SMP 

option)

 WARNING

•  During measurement, light is transmitted from the light source ports. Do not disconnect the 

connected optical fiber cables. Visual impairment may occur if the light enters the eye.

•  Close the covers of any light source ports that do not have optical fiber cables connected 

to them. Visual impairment may occur if light that is mistakenly emitted from these ports 
enters the eye.

French

 AVERTISSEMENT

•  Lorsque l’AQ7280 génère de la lumière, la lumière est émise à travers les ports de source 

lumineuse. Ne pas débrancher les câbles de fibre optique connectés. Des lésions oculaires 
peuvent être causées si le faisceau lumineux pénètre l’œil.

•  Couvrir les caches des ports de source lumineuse libres. Sur les modèles dotés de deux 

ports de source lumineuse ou plus, protéger les yeux contre l’émission accidentelle de 
lumière depuis le mauvais port.

The AQ7280 is equipped with a feature that detects various events along the optical fiber cable route 
and displays them as icons. This feature works by performing an OTDR averaged measurement and 
then automatically performing an OTDR event analysis after the measurement is complete.
Detailed event analysis results are displayed along with the icon of each event.

Procedure

Setup Menu

1.

  From the top menu, select 

OTDR Smart Mapper

.

2.

 Press 

SETUP

 to display the Setup menu.

 

  

Set the measurement conditions.

Set the analysis conditions.

Configure the waveform display.

See section 3.2.

Configure the system.

See chapter 7.

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Eaton IQ 100 series User & Installation Manual preview
IQ 100 series
Brand: Eaton Pages: 87
Eaton Cutler-Hammer Instruction Leaflet preview
Cutler-Hammer
Brand: Eaton Pages: 16
Ebtron GP1 Quick Installation Manual preview
GP1
Brand: Ebtron Pages: 5
Okolab LEO Quick Instructions preview
LEO
Brand: Okolab Pages: 4
Ralston Instruments LC10 Series Quick Start Manual preview
LC10 Series
Brand: Ralston Instruments Pages: 52
Yamaha Clavinova CVP-805 Reference Manual preview
Clavinova CVP-805
Brand: Yamaha Pages: 112
Yamaha Clavinova CLP-270 Data List preview
Clavinova CLP-270
Brand: Yamaha Pages: 44
Yamaha DGX-650 Reference preview
DGX-650
Brand: Yamaha Pages: 3
E Instruments E4500 Operating & Maintenance Manual preview
E4500
Brand: E Instruments Pages: 144
GARANT ST2 Instruction Handbook Manual preview
ST2
Brand: GARANT Pages: 368
Keeler D-KAT R Instructions For Use Manual preview
D-KAT R
Brand: Keeler Pages: 54
Blue-White FLEXFLO M4 Series Operating Manual preview
FLEXFLO M4 Series
Brand: Blue-White Pages: 64
ERICHSEN 518 USB Operating Manual preview
518 USB
Brand: ERICHSEN Pages: 33
SARAD Radon Scout Home Manual preview
Radon Scout Home
Brand: SARAD Pages: 2
TCS QWL4.1 Installation Manual preview
QWL4.1
Brand: TCS Pages: 45
SPX RADIODETECTION 6100 Series Important Safety Instructions Manual preview
RADIODETECTION 6100 Series
Brand: SPX Pages: 6
Kawai Digital Piano CN41 Owner'S Manual preview
Digital Piano CN41
Brand: Kawai Pages: 80
LCR LQ-9101 User Manual preview
LQ-9101
Brand: LCR Pages: 32

Brands by name

Popular brands

Load more brands