manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

5-1

IM AQ7280-01EN

Optical Output and Optical Power Measurement

1

2

3

4

5

6

7

8

Index

5.1  Outputting Light (/SLS option, VLS)

 WARNING

•  During measurement, light is transmitted from the light source ports. Do not disconnect the 

connected optical fiber cables. Visual impairment may occur if the light enters the eye.

•  Close the covers of any light source ports that do not have optical fiber cables connected 

to them. Visual impairment may occur if light that is mistakenly emitted from these ports 
enters the eye.

French

 AVERTISSEMENT

•  Lorsque l’AQ7280 génère de la lumière, la lumière est émise à travers les ports de source 

lumineuse. Ne pas débrancher les câbles de fibre optique connectés. Des lésions oculaires 
peuvent être causées si le faisceau lumineux pénètre l’œil.

•  Couvrir les caches des ports de source lumineuse libres. Sur les modèles dotés de deux 

ports de source lumineuse ou plus, protéger les yeux contre l’émission accidentelle de 
lumière depuis le mauvais port.

Outputting Measurement Light (/SLS option of the OTDR unit)

1.

  From the top menu, select 

Light Source

 to display the following screen.

 

  

Turns the light on

The measurement light turns on. A mark appears on 

the AQ7280 display to indicate that the light is on.

Turns the light off

The light turns off.  The light mark disappears.

Set the wavelength.

The available options vary depending on 

the OTDR unit.

Set the modulation mode.

The available options vary depending on 

the OTDR unit.

Emission wavelength

Chapter 5 

Optical Output and Optical Power Measurement

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Baker Hughes Masoneilan 12400 Series Instruction Manual & Safety Manual preview
Masoneilan 12400 Series
Brand: Baker Hughes Pages: 81
dallmeier SMatrix DMX2400 Commissioning preview
SMatrix DMX2400
Brand: dallmeier Pages: 12
Keithley 617 Quick Reference Manual preview
617
Brand: Keithley Pages: 55
Sanmenxia ZX400 Operation Manual preview
ZX400
Brand: Sanmenxia Pages: 17
SANKO SM-1100 Instruction Manual preview
SM-1100
Brand: SANKO Pages: 25
Samson 2162 Parts And Technical Service Manual preview
2162
Brand: Samson Pages: 2
Yamaha Portable Grand DGX-670 Reference Manual preview
Portable Grand DGX-670
Brand: Yamaha Pages: 93
Yamaha Portatone PSR-410 Manual De Instrucciones preview
Portatone PSR-410
Brand: Yamaha Pages: 65
LEM EM4TII+ Manual preview
EM4TII+
Brand: LEM Pages: 33
Axio MET AX-T2200 Quick Start Manual preview
AX-T2200
Brand: Axio MET Pages: 5
CTC Union PRO VPR100 Series Product Manual preview
PRO VPR100 Series
Brand: CTC Union Pages: 10
PCB Piezotronics 354B33 Installation And Operating Manual preview
354B33
Brand: PCB Piezotronics Pages: 15
Sercel GRC ESP Series Field Installation Manual preview
GRC ESP Series
Brand: Sercel Pages: 63
M & I Instruments DT-86 Instruction Manual preview
DT-86
Brand: M & I Instruments Pages: 3
PASCO SF-9500A Instruction Sheet preview
SF-9500A
Brand: PASCO Pages: 2
Observator Instruments Analite NEP-5000 Manual preview
Analite NEP-5000
Brand: Observator Instruments Pages: 103
Kawai CN25 Operation Manual preview
CN25
Brand: Kawai Pages: 2
SIGRIST OilGuard 2 W Instruction Manual preview
OilGuard 2 W
Brand: SIGRIST Pages: 84

Brands by name

Popular brands

Load more brands