manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

4-1

IM AQ7280-01EN

Optical 

Pulse Analysis

1

2

3

4

5

6

7

8

Index

4.1  Analyzing Waveforms

Switching the Waveform to Be Analyzed

When data measured under multi wavelength conditions is loaded into the AQ7280, a soft key for 
switching the waveform with the wavelength to be analyzed appears on the OTDR menu.

1.

  From the top menu, select 

OTDR

.

2.

  Press the 

Current Trace

 soft key to switch the waveform with the wavelength to be analyzed.

 

  

Switches the current trace

Switches the trace displayed on the screen

How to Use Cursors

1.

  From the top menu, select 

OTDR

.

2.

  Turn the rotary knob to display the cursor.

 

  

Cursor (crosshair cursor example)

Note

•  The direction that the cursor moves differs depending on the direction that you rotate the rotary knob.

  Clockwise: The cursor moves to the right.
  Counterclockwise: The cursor moves to the left.

•  If you turn the rotary knob counterclockwise to the point where the cursor reaches the left side of the 

screen, the cursor will disappear. If you reach the measurement end point, the cursor will not move 
forward even if you turn the rotary knob clockwise.

•  For details on the cursor display format, see section 3.2.
•  You can change the cursor movement resolution (fine or coarse). For the procedure, see section 3.3.

Chapter 4 

Optical Pulse Analysis

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Yamaha 142 Quick Operation Manual preview
142
Brand: Yamaha Pages: 2
palintest Micro 800 Operating Instructions Manual preview
Micro 800
Brand: palintest Pages: 14
jenway 6405 Operating Manual preview
6405
Brand: jenway Pages: 52
Grundfos Vortex Flow Industry Instructions Manual preview
Vortex Flow Industry
Brand: Grundfos Pages: 16
Spacelabs 91390 Operation Manual preview
91390
Brand: Spacelabs Pages: 156
Dwyer Instruments PSX2 Instruction Manual preview
PSX2
Brand: Dwyer Instruments Pages: 189
Lowrey tribute Player'S Manual preview
tribute
Brand: Lowrey Pages: 109
Neogen Corporation AccuPoint 2 ATP Manual preview
AccuPoint 2 ATP
Brand: Neogen Corporation Pages: 16
Gates 507C Manual preview
507C
Brand: Gates Pages: 112
DODODUCK Q63 Instruction Manual preview
Q63
Brand: DODODUCK Pages: 2
Spasciani M 900 ABEK 15 Instructions For Use Manual preview
M 900 ABEK 15
Brand: Spasciani Pages: 26
EPE Conseil ESI 22 Quick Start Manual preview
ESI 22
Brand: EPE Conseil Pages: 3
Primes Cube L1 Operating Manual preview
Cube L1
Brand: Primes Pages: 48
MULTISPAN AMP-23 Operating Manual preview
AMP-23
Brand: MULTISPAN Pages: 4
Wacom SD-310E User Manual preview
SD-310E
Brand: Wacom Pages: 23
VECTECH 492EP Operation Manual preview
492EP
Brand: VECTECH Pages: 10
ICON truflo TC Series Operating Manual preview
truflo TC Series
Brand: ICON Pages: 6
RBR quartz3 BPR zero Manual preview
quartz3 BPR zero
Brand: RBR Pages: 22

Brands by name

Popular brands

Load more brands