YOKOGAWA AQ7280 OTDR User Manual Download Page 53

Page: 53 / 195

2-28

IM AQ7280-01EN

Cable Installation Completion Notification

On the OTDR menu, press the

Advanced Measurement

soft key and then the

Work

Completion Notice

soft key. The following screen appears.

Turns the completion notification

on or off

Turns the message display on or off
Turns the alarm on or off
Set the confirmation (No Check,

Check only once, Check everytime).

Set Notification to

Set Message to

Press

REAL TIME

to start a measurement. The screen shows the measurement waveform, and

the RealTime menu appears. The words “Check Point” appears at the cursor on the screen.

Press the

Next

soft key and then the

Completion Check

soft key to select ON.

When the measurement to the Check Point distance is complete, a completion message is displayed.

Set the work completion

confirmation (ON, OFF).

When the work completion notice is set to ON,

“CheckPoint” appears at the cursor.

End of fiber

Move the cursor to a

position that is slightly

after the installation

point.

You can perform measurements efficiently by moving the cursor to a position

slightly after the installation point (depending on how fast the optical fiber cable will

be installed). This is because the AQ7280 notifies you of the work completion, which

is your sign to measure the connection loss at that point (splice, connection, etc.).

2.5 Performing Real-time Measurement

Summary of Contents for AQ7280 OTDR




































































































































































































Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands

YOKOGAWA AQ7280 OTDR, User Manual

Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands