manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

4-2

IM AQ7280-01EN

How to Use Markers

You can use markers to measure values such as the distance, splice loss, or return loss between two 
points.

Marker Menu (Marker Mode: Marker)

1.

  From the top menu, select 

OTDR

.

2.

  Press the 

Marker

 soft key to display the marker menu.

Switches to the screen that is used to measure 2 Point markers.

For the measurement principle, see section 1.4.

Switches to the screen that is used to measure 4 Point markers.

For the measurement principle, see section 1.4.

Switches to the screen that is used to 

measure 6 Point markers.

For the measurement principle, see 

section 1.4.

Sets or clears the distance 

reference.

Sets the distance reference 

(marker R) at the cursor position.

Clears the markers and cursors.

Preset markers.

Register markers that you set in advance, 

and apply them on waveforms during 

measurement when necessary.

2 Point Markers

  Press the 

2 Point Markers

 soft key to display the following screen.

Sets marker      .

Marker

      

is set at the cursor 

position.

1

1

Sets marker      .

Marker

      

is set at the cursor 

position.

2

2

Turns the cursor link on or off

1

Marker

2

Marker

Marker information

Note

•  When you set the marker positions, set them so that the 

1

 marker is the measurement start point (the 

distance reference).

•  The measured loss value differs depending on the specified approximation method.

4.1  Analyzing Waveforms

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

E Instruments 1500 Quick Manual preview
1500
Brand: E Instruments Pages: 2
Ebtron GP1 Quick Installation Manual preview
GP1
Brand: Ebtron Pages: 5
Okolab LEO Quick Instructions preview
LEO
Brand: Okolab Pages: 4
National Instruments PXIe-5665 Calibration Manual preview
PXIe-5665
Brand: National Instruments Pages: 85
National Instruments PXIe-5622 Getting Started Manual preview
PXIe-5622
Brand: National Instruments Pages: 12
National Instruments PXIe-4163 Manual preview
PXIe-4163
Brand: National Instruments Pages: 18
National Instruments USB-5683 Getting Started Manual preview
USB-5683
Brand: National Instruments Pages: 12
Olympus IV0620C Operation Manual preview
IV0620C
Brand: Olympus Pages: 12
Daewoo D-60 User Manual preview
D-60
Brand: Daewoo Pages: 17
Keit IRmadillo DOC1048R User Manual preview
IRmadillo DOC1048R
Brand: Keit Pages: 27
YOSensi YO Meter Pulse User Manual preview
YO Meter Pulse
Brand: YOSensi Pages: 27
Datakom DV-0101 Quick Start Manual preview
DV-0101
Brand: Datakom Pages: 2
Kinesys LibraCELL User'S Product Manual preview
LibraCELL
Brand: Kinesys Pages: 10
REED SD-4214 Instruction Manual And Users Manual preview
SD-4214
Brand: REED Pages: 20
Medical International Research spirodoc User Manual preview
spirodoc
Brand: Medical International Research Pages: 46
Amazing Machinery Viztrac AM 200 User Manual preview
Viztrac AM 200
Brand: Amazing Machinery Pages: 18
Simrad PI44 C Operator'S Manual preview
PI44 C
Brand: Simrad Pages: 322
Futech 039.05 User Manual preview
039.05
Brand: Futech Pages: 68

Brands by name

Popular brands

Load more brands