YOKOGAWA AQ7280 OTDR User Manual Download Page 132 | Manualshive

Page: 132 / 195

background image

6-1

IM AQ7280-01EN

File Operation and Printing

1

2

3

4

5

6

7

8

Index

6.1 Connecting USB Storage Media to the USB Ports

CAUTION

Do not remove a USB memory device or turn off the power when the USB memory access
indicator is blinking or when data is being saved or loaded from internal memory. Doing so
may damage the storage medium (USB memory or internal memory) or corrupt its data.

French

ATTENTION

N’enlevez pas un dispositif de mémoire USB et ne coupez pas l’alimentation électrique
lorsque l’indicateur d’accès à la mémoire USB clignote ou lorsque les données sont en train
d’être enregistrées ou chargées à partir d'une mémoire interne. Vous risqueriez
d’endommager le support de stockage (mémoire USB ou mémoire interne) ou les données
qu’il contient.

Use a portable USB memory device for the USB storage media. Connect it directly to a type A USB
port of the AQ7280.
Hot-plugging is supported: you can connect or disconnect the USB device at any time, regardless of
whether the AQ7280 is on or off.
When the power is on, the AQ7280 automatically detects the USB memory device after it is connected.

Note

• Use a portable USB memory device for the USB storage media. Do not connect incompatible USB

memory devices.

•  Connect USB memory devices directly to the AQ7280, not through a USB hub.
•  You cannot use protected USB memory devices (such as those that contain encrypted content).
•  Do not remove and connect a USB memory device at short intervals. Provide at least a 10-second interval

between removal and connection.

• Do not connect or remove a USB memory device from the time when the AQ7280 is turned on until key

operation becomes available.

• USB memory devices complying with USB 1.0/1.1/2.0 can be used.

Chapter 6

File Operation and Printing

«
...
130
131
132
133
134
...
»

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Brand: Keithley Pages: 48

Brand: Dallas Brass Pages: 19

Brand: IET Labs Pages: 114

A300 Sport.Tool

Brand: Navman Pages: 1

Brand: Gearx Pages: 19

Brand: Dakota Digital Pages: 34

Brand: Value Pages: 20

Brand: D-tect Systems Pages: 2

Brand: BK Precision Pages: 21

Brand: Vaisala Pages: 2

Brand: SKF Pages: 12

Brand: Ocean Reef Pages: 20

Brand: E+E Elektronik Pages: 3

Celviano GP-300

Brand: Casio Pages: 78

Brand: Modern Water Pages: 17

Brand: Vortex Pages: 11

Brand: A&A Tech Pages: 18

Brand: Aqua Lung Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands