manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

8-14

IM AQ7280-01EN

8.8  Replacing the Optical Adapter

 WARNING

When replacing the optical adapter, turn off the AQ7280 to prevent the light from accidentally 
being emitted from the light source port. Replacing the optical adapter (universal adapter or 
connector adapter) with the AQ7280 turned on may cause the emitted light to accidentally 
enter the eye. This can cause eye damage or vision impairment.

French

 AVERTISSEMENT

Lors du remplacement d'un adaptateur optique, mettre l'AQ7280 hors tension pour empêcher 
l'émission accidentelle de lumière depuis le port de la source lumineuse. Le remplacement de 
l'adaptateur optique (adaptateur universel) ou 
(adaptateur de connecteur) avec l'AQ7280 sous tension peut permettre à la lumière émise de 
pénétrer accidentellement dans les yeux. Ceci peut provoquer des lésions oculaires ou une 
déficience visuelle.

Removal

1.

  Check that the AQ7280 is turned off.

2.

  Open the optical port cover.

3.

  Flip the optical adapter’s lock lever down inward to release the lock. If it is a screw type, turn 

the knob to the left to loosen.

4.

  Pull out the optical adapter.

 

  

Lock lever

Knob (screw type)

Note

•  A lock lever type optical adapter is installed in the OTDR unit.
•  A screw type optical adapter is installed in the optical power measurement port of the OPM module.
•  If the optical port cover comes off, bend the cover axle with your fingers and reattach it.

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Hammond Skx PRO Reference Manual preview
Skx PRO
Brand: Hammond Pages: 754
E Instruments E500 Quick Manual preview
E500
Brand: E Instruments Pages: 2
UE Systems Ultraprobe 9000 Manual preview
Ultraprobe 9000
Brand: UE Systems Pages: 25
UE Systems ULTRAPROBE 10000 General Setup And Knowledge preview
ULTRAPROBE 10000
Brand: UE Systems Pages: 6
Unitech UT-1405 Instruction Manual preview
UT-1405
Brand: Unitech Pages: 18
Evoqua WALLACE & TIERNAN P7 ADVANCED Instruction Manual preview
WALLACE & TIERNAN P7 ADVANCED
Brand: Evoqua Pages: 98
OHAUS STARTER 3100C Instruction Manual preview
STARTER 3100C
Brand: OHAUS Pages: 84
MADDALENA microCLIMA ULTRA Installation And Operating Instructions Manual preview
microCLIMA ULTRA
Brand: MADDALENA Pages: 17
Camlab CW/6230 Instruction Manual preview
CW/6230
Brand: Camlab Pages: 28
Hanna Instruments HI 991301 Instruction Manual preview
HI 991301
Brand: Hanna Instruments Pages: 2
Vogel 65 7120 Operation Manual preview
65 7120
Brand: Vogel Pages: 4
Vaisala K-PATENTS PR-23 AX Series Instruction Manual preview
K-PATENTS PR-23 AX Series
Brand: Vaisala Pages: 246
Magnetrol CONTOUR 3DS-S Installation And Operating Manual preview
CONTOUR 3DS-S
Brand: Magnetrol Pages: 48
Redi-Chek Roast Alert/3 ET-8C Instruction Manual preview
Roast Alert/3 ET-8C
Brand: Redi-Chek Pages: 3
Sper scientific AquaShock 850046K User Manual preview
AquaShock 850046K
Brand: Sper scientific Pages: 28
Seli STS-15 Manual preview
STS-15
Brand: Seli Pages: 68
Ceyear 3656 Series Quick Start Manual preview
3656 Series
Brand: Ceyear Pages: 53
Hanna Instruments HI 96831 Instruction Manual preview
HI 96831
Brand: Hanna Instruments Pages: 20

Brands by name

Popular brands

Load more brands