YOKOGAWA AQ7280 OTDR User Manual Download Page 171

Page: 171 / 195

7-11

IM AQ7280-01EN

System Configuration

Index

7.6 Other Features

Procedure

System Setup Screen

Press

SETUP

and then the

System Setup

soft key to display the following screen.

When the screen is scrolled

Configure the language settings.

The options are displayed according to the

language suffix code.

Turns touch operation on or off

Executes initialization

See section 7.2.

Set the date and Time.

See the Getting Started Guide, IM AQ7280-02EN.

Set the power save mode.

See section 7.1.

Set the start menu

(Top Menu, Last Function).
Sets the screen color

(Color 1, Color 2, B&W)

Turns the beep sound on or off
Set the function to assign to the UTIL key

(Print Execute, Report Execute, Utility Menu,

Power Meter, Power Checker, Light Source,

VLS, Fiber Inspec. Probe, File Name Setup).
Set the file list.

See section 6.9.

Set operation restrictions.

See section 7.3.

Set the USB function (Control I/O, Storage).

Configure the network settings.

See section 7.4.

Set the FlashAir auto timeout value.

( Off, 5m, 10m, 20m, 30m)

Confirms the settings

Cancels the settings

Configure FlashAir.

Explanation

Language

Set the language used on the AQ7280 screen. The options are displayed according to the language
suffix code of each product. For details on the language suffix codes, see the Getting Started Guide,
IM AQ7280-02EN.

Start Menu

Set the first screen that appears when you start the AQ7280.

Top Menu

The top menu appears.

Last Function

The screen that was displayed immediately before the power was turned off appears when you

start the AQ7280.

Summary of Contents for AQ7280 OTDR




































































































































































































Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands

YOKOGAWA AQ7280 OTDR, User Manual

Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands