YOKOGAWA AQ7280 OTDR User Manual Download Page 54

Page: 54 / 195

2-29

IM AQ7280-01EN

Optical Pulse Measurement (OTDR)

Index

Explanation

Real-time Measurement

Measurement conditions are set before the actual measurement takes place, but during real-time

measurement you can change the measurement conditions and adjust markers and the cursor. When

you stop a measurement, the AQ7280 returns to the previous screen.

• In Simple mode, you can only change the wavelength.

• You cannot change the attenuation if the average method is set to High Resolution. For details, see

page 2-7.

Cable Installation Completion Notification

Before you check whether the work is complete, move the cursor slightly after the extension work

point or before the work completion point on the optical fiber cable, and turn on the work completion

notification. When the fiber end detection position (the event) during real-time measurement is the

same as the cursor position (CheckPoint), the AQ7280 gives a notification (message indication and

alarm sound) that the cable installation is complete.

Construction start

position

Distance

Level

Extension work point

(splice, connection, etc.)

Work completion point

Work completion notification

cursor position

50 km

100 km

(Event)

Completion notification

cursor position during

optical fiber cable

extension

CheckPoint

2.5 Performing Real-time Measurement

Summary of Contents for AQ7280 OTDR




































































































































































































Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands

YOKOGAWA AQ7280 OTDR, User Manual

Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands