YOKOGAWA AQ7280 OTDR User Manual Download Page 161 | Manualshive

Page: 161 / 195

background image

7-1

IM AQ7280-01EN

System Configuration

1

2

3

4

5

6

7

8

Index

7.1 Setting the Power Save Mode

Even when you set LCD Brightness to OFF, if you press a panel key, the backlight turns on at the “Power
save” brightness level.
If you do not perform any operations for 10 seconds, the backlight automatically turns off. This feature
is useful when you move the AQ7280 to a dark place after setting LCD Brightness to OFF.

Procedure

Power Save Setup Screen

1.

Press

SETUP

.

2.

Using the

rotary knob

and

ENTER

, select

Power Save

to display the following screen.

When using the AC adapter

When using the battery

Set the LCD brightness

(Bright, Normal, Power save, OFF).

Set the auto power off feature

(OFF, 1m, 5m, 10m, 30m).
Set the LCD brightness

(Bright, Normal, Power save, OFF).
Turns the screen saver on or off

Explanation

You can specify separate power save settings for AC adapter operation and battery pack operation.

Auto Power OFF

If the AQ7280 is left standing for a certain period with the power turned on, the power will be
automatically turned off. The power will not be automatically turned off, however, when measuring with
the OTDR feature.

OFF

The power will not be turned off.

1m

If you do not operate the AQ7280 for 1 minute, the power will be automatically turned off.

5m

If you do not operate the AQ7280 for 5 minutes, the power will be automatically turned off.

10m

If you do not operate the AQ7280 for 10 minutes, the power will be automatically turned off.

30m

If you do not operate the AQ7280 for 30 minutes, the power will be automatically turned off.

LCD Brightness

You can set the LCD brightness.

Bright

The screen is set bright. Use this setting in a bright environment. This setting uses a lot of power.

During battery pack operation, pay attention to the battery level.

Normal

Normal brightness.

Power save

Slightly darker the normal brightness. This setting can be used in a dark environment. The battery

pack lasts longer than the Normal setting.

OFF

The LCD backlight is turned off. The battery pack lasts longer, even longer than the Power save

setting. When you press any key, the backlight turns on for approximately 10 seconds.

Turning the Screen Saver On and Off

When the AQ7280 is running of battery, the display will turn off automatically after 15 seconds of no
user activity. Press any key to turn on the display. Touch panel operations are not possible in screen
save mode.

Chapter 7

System Configuration

«
...
159
160
161
162
163
...
»

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

Brand: Kawai Pages: 33

Brand: Kawai Pages: 60

Brand: Underground Magnetics Pages: 48

Brand: PITSID Pages: 22

Brand: Swan Analytical Instruments Pages: 102

Microlog GX Series

Brand: SKF Pages: 342

Brand: Magnescale Pages: 2

Brand: Datakom Pages: 27

Brand: SANKO Pages: 97

Brand: Staco Energy Pages: 2

Brand: JensPrima Pages: 20

SoundExpert LxT

Brand: Larson Davis Pages: 307

Brand: ERICHSEN Pages: 33

MASTERVISION ECO

Brand: Ega Master Pages: 48

Brand: AquaMetrix Pages: 37

Brand: GCI Pages: 44

Brand: Oakton Pages: 10

PCV100-F200-B17-V1D-6011

Brand: Pepperl+Fuchs Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands