YOKOGAWA AQ7280 OTDR User Manual Download Page 153

Page: 153 / 195

6-22

IM AQ7280-01EN

Explanation

Action

Select Report or File Report.
Report: The current waveform displayed on the screen is included in the report and exported

to PDF.

File Report: Waveform data from a saved file is selected for the report and exported to PDF.

Save Destination Drive

For details, see the explanation in section 6.3.

Report Form

• Fiber Surface Image

Set how to include the fiber end face image (BMP format) in the report form.

OFF

The fiber end face image is not included.

Manual

Select the fiber end face image to include (through file operation) at the time a report is

created. This option is not available when File Report is executed.

Auto

When there is a fiber end face image in BMP format with a same ID number (see page 6-9)

as that of the waveform data in SOR format to be included in the report, the image data is

automatically selected and included in the report.

It is included as shown below.

Image

• Measure Conditions

The following information is included.
Information such as label and company name can be specified in the file name label when the

file action is set to Save. Set these if necessary. For details, see section 6.3.

Label

Originating Loc

Company Name

Terminating Loc

Name

Current Data Flag

Fiber ID

Supplier Name

Fiber Type

Model Name

Cable ID

Unit Name

Cable Code

FW Ver.

1, 2

Report Date

1 Automatically included by the AQ7280

2 Firmware version

• Measured Results

The following information is included.

•  Total distance
•  Total loss
•  Total return loss
•  Number of events
•  Fault events
•  Pass/fail judgments

6.8 Creating Reports of Waveform Data as PDF Data

Summary of Contents for AQ7280 OTDR




































































































































































































Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands

YOKOGAWA AQ7280 OTDR, User Manual

Search results

Summary of Contents for AQ7280 OTDR

Reviews:

Related manuals for AQ7280 OTDR

Brands by name

Popular brands