manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

8-9

IM AQ7280-01EN

Troubleshooting, Maintenance, and Inspection

1

2

3

4

5

6

7

8

Index

8.6  Checking the Optical Fiber End Face for Stains

By connecting an off-the-shelf fiber inspection probe (with a USB interface) to an AQ7280 USB port, you 
can display the image of optical fiber end face on the AQ7280 display. You can save the image to a file.

Procedure

Fiber End Face Check Screen

From the top menu, select 

FiberInspec. Probe

 to display the following screen. 

 

Displays the image in real time

Holds the image display (HOLD)

Start saving

Press this soft key to save the screen 

that is displayed. For the procedure 

to set the file save destination, file 

type, and file name, see section 6.3.

The name of the file that will be saved the next time

Pass/Fail Judgment (/FST Option)

AQ7280 firmware versions 1.07 and later support this function.
A judgment is performed on scratches and defects detected in the end face image, and those that 
exceed the specified threshold are displayed as fail (Fail).

1.

  From the top menu, select 

FiberInspec. Probe

 to display the following screen.

 

  

Executes judgment

Executes pass/fail judgment 

and displays the judgment 

results (summary).

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

ABB Navigator 550 Commissioning Instructions preview
Navigator 550
Brand: ABB Pages: 8
Oldham BM25 Operating Manual preview
BM25
Brand: Oldham Pages: 43
Task Force Tips BLITZFIRE Series Instruction For Operation And Maintenance preview
BLITZFIRE Series
Brand: Task Force Tips Pages: 20
Yamaha AW2816 Tutorial preview
AW2816
Brand: Yamaha Pages: 31
Danfoss LLG Installation Manual preview
LLG
Brand: Danfoss Pages: 4
WATERGUARD V21I Installation Manual preview
V21I
Brand: WATERGUARD Pages: 2
Bühler technologies S-SM Installation And Operation Instruction Manual preview
S-SM
Brand: Bühler technologies Pages: 33
Hanna Instruments HI 84430 Instruction Manual preview
HI 84430
Brand: Hanna Instruments Pages: 25
Sierra C100L-L-DD-LE-5-OV1-SV1-PV1C-V1-S1 Instruction Manual preview
C100L-L-DD-LE-5-OV1-SV1-PV1C-V1-S1
Brand: Sierra Pages: 55
STM eDrometer Owner'S Manual preview
eDrometer
Brand: STM Pages: 31
Eaton 3 601 K76 710 Manual preview
3 601 K76 710
Brand: Eaton Pages: 13
RIDGID SeeSnake microReel Manual preview
SeeSnake microReel
Brand: RIDGID Pages: 414
Kawai Digital Piano CN41 Owner'S Manual preview
Digital Piano CN41
Brand: Kawai Pages: 80
LCR LQ-9101 User Manual preview
LQ-9101
Brand: LCR Pages: 32
Lasertec HV2G Instruction Manual preview
HV2G
Brand: Lasertec Pages: 28
janitza UMG 96 RM-CBM Installation Manual preview
UMG 96 RM-CBM
Brand: janitza Pages: 12
Downeaster Wind & Weather Medallion Series Instruction Manual preview
Wind & Weather Medallion Series
Brand: Downeaster Pages: 2
Umarex Laserliner AutoCross-Laser 2 XP Operating Instructions Manual preview
Laserliner AutoCross-Laser 2 XP
Brand: Umarex Pages: 68

Brands by name

Popular brands

Load more brands