manualshive.com logo in svg

YOKOGAWA AQ7280 OTDR, User Manual

The YOKOGAWA AQ7280 OTDR is a cutting-edge optical time domain reflectometer. Ensure a smooth setup and operation with the comprehensive Getting Started Manual available for free download on our website. Discover all the essential information and step-by-step instructions to maximize the potential of this advanced product.

Share
Download
background image

8-11

IM AQ7280-01EN

Troubleshooting, Maintenance, and Inspection

1

2

3

4

5

6

7

8

Index

Displaying Judgment Results (Details)

4.

  Press the 

Result

 soft key to display the following screen.

 

  

Results in the core area

Results in the cladding area 

(excluding the core area)

Results in the contact area 

(excluding the core and 

cladding areas)

Explanation

Connecting a Fiber Inspection Probe

Hot-plugging is supported; you can connect or disconnect a USB device at any time, regardless of 
whether the AQ7280 is on or off.
If you connect a USB fiber inspection probe while the AQ7280 is on, the AQ7280 will automatically 
identify the probe.
For notes on connecting USB devices, see Note in section 6.1.
For information about compatible fiber inspection probes, contact your nearest YOKOGAWA dealer.

Holding the Image Display

The still image size is VGA for both the USB2.0 and USB1.1 fiber inspection probes.

Note

If a USB2.0 fiber inspection probe is connected, it will take some time to display the still image.

Saving the Screen Image

You can save the still image. Video cannot be saved.

8.6  Checking the Optical Fiber End Face for Stains

Summary of Contents for AQ7280 OTDR




































































































































































































Reviews:

No comments

Related manuals for AQ7280 OTDR

QLA KT2 Operating Instructions Manual preview
KT2
Brand: QLA Pages: 18
Eaton CMD Manual preview
CMD
Brand: Eaton Pages: 43
Vanguard Instruments II Series Operating Instructions Manual preview
II Series
Brand: Vanguard Instruments Pages: 24
Hama TH-200 Operating Instruction preview
TH-200
Brand: Hama Pages: 6
Teledyne Analytical Instruments 3020 M Operating Instructions Manual preview
3020 M
Brand: Teledyne Analytical Instruments Pages: 107
Apogee MQ-100X Owner'S Manual preview
MQ-100X
Brand: Apogee Pages: 22
Lennox Smart Air Quality Monitor Installation And Setup Manual preview
Smart Air Quality Monitor
Brand: Lennox Pages: 28
Roland KR-1070 Owner'S Manual preview
KR-1070
Brand: Roland Pages: 96
Floyd Rose SPEEDLOADER BRIDGE SYSTEM Manual preview
SPEEDLOADER BRIDGE SYSTEM
Brand: Floyd Rose Pages: 10
HBM T10F Mounting Instructions preview
T10F
Brand: HBM Pages: 84
Velleman NETBSEM User Manual preview
NETBSEM
Brand: Velleman Pages: 15
Konica Minolta CM-3700A Instruction Manual preview
CM-3700A
Brand: Konica Minolta Pages: 42
Kobold KSK Operating Instructions Manual preview
KSK
Brand: Kobold Pages: 12
Danfoss SonoSelect 10 Installation & User Manual preview
SonoSelect 10
Brand: Danfoss Pages: 16
Ibravebox V8 Finder User Manual preview
V8 Finder
Brand: Ibravebox Pages: 32
Xylem Ai1 Series Quick Start Manual preview
Ai1 Series
Brand: Xylem Pages: 39
Righton Retinomax K+Screeen Instructions Manual preview
Retinomax K+Screeen
Brand: Righton Pages: 112
Mahr Multimar 25 EWR Operating Instructions Manual preview
Multimar 25 EWR
Brand: Mahr Pages: 20

Brands by name

Popular brands

Load more brands