YOKOGAWA AQ2200 Series User Manual Download Page 182

Page: 182 / 183

Index-1

IM 735101-01EN

Index

Page

HOLD.................................................................................... 1-3

Page

instrument information, displaying ...................................... 4-26

instrument, storing ................................................................ 2-6

interface module ................................................................. 1-10

Page

key operation console........................................................... 1-3

Page

light source modules............................................................. 1-5

LS module ............................................................................ 1-6

Page

MACRO ................................................................................ 1-3

maximum power consumption ............................................ 2-26

module device information, displaying................................ 4-23

module, installing ................................................................ 2-10

modules, changing ............................................................. 4-16

modules, installing and uninstalling ...................................... 2-9

module, uninstalling ............................................................. 2-11

Page

optical connectors, how to clean ........................................ 4-30

optical fiber cables, connecting .......................................... 2-24

optical interfaces, tools required for cleaning ..................... 4-30

optical modulator module ..................................................... 3-8

optical modulator modules.................................................. 1-22

optical receiver module................................................ 1-23, 3-9

optical sensor head ............................................................. 1-11

optical sensor modules ................................................ 1-10, 3-3

optical switch modules........................................................ 1-18

ORL module ....................................................................... 1-14

OSW module .................................................... 1-18, 1-19, 1-20

Page

periodic calibration.............................................................. 4-35

power supply, connecting to ............................................... 2-25

PRESET ............................................................................... 1-3

PRTSC ................................................................................. 1-3

Page

rack mounting ....................................................................... 2-5

rated supply frequency ....................................................... 2-26

rated supply voltage ........................................................... 2-26

recommended replacement parts ....................................... 4-34

REF CLOCK IN ........................................................... 3-7, 3-1 1

REMOTE INTERLOCK ......................................................... 3-1

Page

sensor module (dual) .......................................................... 1-13

sensor module (highly sensitive type) ................................ 1-12

sensor module (high power type) ....................................... 1-12

SG Module.......................................................................... 1-26

SHIFT ................................................................................... 1-3

Numerics

Page

10 Gbit/s BERT module ...................................................... 1-21

10 Gbit/s optical modulator (wavelength: 1.31 μm)

............ 1-22

10 Gbit/s optical modulator (wavelength: 1.55 μm)

............ 1-22

10 Gbit/s optical receiver .................................................... 1-23

100 V .................................................................................. 2-26

200 V .................................................................................. 2-26

Page

accessories, optional ............................................................... iv

accessories, standard.............................................................. iv

ANALOG OUT ...................................................................... 3-3

ANGLED PC ONLY ............................................................ 2-24

APPLI ................................................................................... 1-3

AQ9335C connector adapter .............................................. 2-23

AQ9441 universal adapter .................................................. 2-22

AQ9447 connector adapter ................................................ 2-21

attenuator modules ............................................................. 1-15

ATTN module ............................................................. 1-15, 1-16

ATTN module (built-in monitor power meter) ............. 1-16, 1-17

Page

BERT module .............................................................. 1-21, 3-4

blank panel ........................................................................... 2-7

Page

cables, connecting .............................................................. 2-12

CLOCK IN............................................................................. 3-6

CLOCK OUT ......................................................................... 3-6

connector adaptors, connecting and disconnecting ........... 2-21

current module...................................................................... 1-4

current parameter ................................................................. 1-4

Page

DATA IN ....................................................................... 3-8, 3-1 1

DATA IN 1 (CDR) .................................................................. 3-6

DATA IN 2 ............................................................................. 3-6

DATA OUT ................................................................... 3-5, 3-1 1

DATA OUT TO OPTICAL MODULATOR .............................. 3-5

DETAIL ................................................................................. 1-3

DETAIL screen...................................................................... 1-4

DFB-LD module .................................................................... 1-5

DUAL ATTN Module ........................................................... 1-17

DUAL FP-LD module ............................................................ 1-7

DUT ...................................................................................... 3-4

Page

EXT CLOCK IN ..................................................................... 3-7

Page

FILE ...................................................................................... 1-3

firmware, updating .............................................................. 4-19

FP-LD module ...................................................................... 1-7

frame controller.............................................................. 1-1, 3-1

frame controller and modules, cleaning.............................. 4-27

frame controller information, displaying .............................. 4-23

Page

Grid TLS Module .................................................................. 1-8

Index

Summary of Contents for AQ2200 Series
























































































































































































Search results

Summary of Contents for AQ2200 Series

Reviews:

Related manuals for AQ2200 Series

Brands by name

Popular brands

YOKOGAWA AQ2200 Series, User Manual

Search results

Summary of Contents for AQ2200 Series

Reviews:

Related manuals for AQ2200 Series

Brands by name

Popular brands