YOKOGAWA AQ2200 Series User Manual Download Page 122

Page: 122 / 183

Turn the instrument on while holding down the top soft key.

The update screen appears, and the instrument begins updating the firmware automatically.

Top soft key

<< Update Firmware >>

Updating...

Boot Rev. : 1.01-00

FPGA1 Rev. : 0.06-00

Progress S . . . . . . . . -> E

A completion message appears at the bottom of the screen when the update finishes
correctly. After that, the frame controller starts automatically.

<< Update Firmware >>

Updating...

Boot Rev. : 1.01-00

FPGA1 Rev. : 0.06-00

Progress S . . . . . . . . . . . . . -> E

Flash (Firmware) Update Complete

You must reboot this machine

Note

You can disconnect the USB memory device when the frame controller starts to run.

Displaying the Version Information

Press

SYSTEM

to display the SYSTEM screen.

Use the arrow keys to select Soft Version View, and press the

Select

soft key or

ENTER

The SOFTWARE VERSION screen appears. This screen shows the version information for
the frame controller and all of the installed modules.

4.4 Updating the Firmware

4-20

IM 735101-01EN

Summary of Contents for AQ2200 Series
























































































































































































Search results

Summary of Contents for AQ2200 Series

Reviews:

Related manuals for AQ2200 Series

Brands by name

Popular brands

YOKOGAWA AQ2200 Series, User Manual

Search results

Summary of Contents for AQ2200 Series

Reviews:

Related manuals for AQ2200 Series

Brands by name

Popular brands