YOKOGAWA AQ2200 Series User Manual Download Page 84

Page: 84 / 183

2.8 Connecting to the Power Supply

Before Connecting the Power Supply

Make sure to follow the warnings below when connecting the power supply. Failure to do
so may cause electric shock or damage to the instrument.

WARNING

• Make sure that the power supply voltage matches the instrument’s rated supply

voltage and that it does not exceed the maximum voltage range of the power
cord to use.

• Confirm that the frame controller’s power switch is off before connecting the

power cord.

• To prevent electric shock or fire, be sure to use the power cord for the instrument.
• To prevent electric shock, make sure to ground the instrument. Insert the frame

controller’s power cord into a grounded three-prong outlet.

• Do not use an ungrounded extension cord. If you do, the instrument will not be

grounded.

• If an AC outlet that conforms to the supplied power cord is unavailable and you

can not ground the instrument, do not use the frame controller.

French

AVERTISSEMENT

• Assurez-vous que la tension d’alimentation correspond à la tension d’alimentation

nominale de l’appareil et qu’elle ne dépasse pas la plage de tension maximale
du cordon d’alimentation à utiliser.

• Vérifier que l’interrupteur d’alimentation du contrôleur est hors tension avant de

brancher le cordon d’alimentation.

• Pour éviter tout risque de choc électrique, utiliser exclusivement le cordon

d’alimentation prévu pour cet instrument.

• Pour éviter tout risque de choc électrique, l’instrument doit impérativement être

relié à la terre. Insérer le cordon d’alimentation du contrôleur dans une prise à
trois broches reliée à la terre.

• Toujours utiliser une rallonge avec broche de mise à la terre, à défaut de quoi

l’instrument ne serait pas relié à la terre.

• En l’absence de prise CA conforme au cordon d’alimentation fourni et dans

l’impossibilité de mettre l’instrument à la terre, ne pas utiliser le contrôleur.

2-25

IM 735101-01EN

Making Preparations for Measurements

Index

Summary of Contents for AQ2200 Series
























































































































































































Search results

Summary of Contents for AQ2200 Series

Reviews:

Related manuals for AQ2200 Series

Brands by name

Popular brands

YOKOGAWA AQ2200 Series, User Manual

Search results

Summary of Contents for AQ2200 Series

Reviews:

Related manuals for AQ2200 Series

Brands by name

Popular brands