manualshive.com logo in svg

YOKOGAWA AQ2200 Series, User Manual

Share
Download
YOKOGAWA AQ2200 Series User Manual Download Page 81

How to Connect and Disconnect the AQ9441 Universal Adapter

The AQ9441 Universal Adapter can be used with the AQ2200-141 FP-LD and AQ2200-
142 DUAL FP-LD modules.

Connecting the Adapter

1.

  Fit the guide pins of the universal adapter into the guide holes on the rear shell. 

Take care not to let the universal adapter come in contact with the end of the 
ferrule that extends from the rear shell.

 

 

   

AQ9441 Universal Adapter 

Rear shell 

Guide hole 

Guide pin

Ferrule

2.

  Lock the universal adapter by pushing the lock lever down until you hear a click.

 

 

   

Lock lever

Disconnecting the Adapter

1.

  Lift the lock lever on the AQ9441 Universal Adapter to unlock it.

 

 

   

Lock lever

AQ9441 Universal Adapter

2.

  Pull the lock lever toward you, and slowly remove the universal adapter from the 

rear shell.

 

 

   

AQ9441 Universal Adapter

Rear shell

2.6  Connecting and Disconnecting Connector Adapters

2-22

IM 735101-01EN

Summary of Contents for AQ2200 Series
























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands