YOKOGAWA AQ2200 Series User Manual Download Page 36

Page: 36 / 183

Display and Key Operation Console

AQ2211

FRAME CONTROLLER

DETAIL

SLOT

SUMMARY

HOLD

APPLI

FILE

MACRO

SYSTEM

PRTSC

PRESET

SHIFT

CANCEL

ENTER

POWER

USB

Hard keys

Display

Displays information such as measured

values, settings, and status.

CANCEL key

This key is used to cancel operations.

Power switch

This switch is used when you turn the instrument on and off.

Soft keys

The soft keys are used to select and

execute the items that are shown on

the display.

ENTER key

This key is used to set selected items

and entered values.

USB port (type A)

Used when you connect a USB

memory device.

Arrow keys

◄

and

►

are used to change the

selected digit during the input of

numeric values and to input

backspaces and the minus symbol in

keypad mode.

▲ and ▼ are used to change the

module to control, move the cursor,

and change numeric values.

Hard Keys

Key Name

Description

DETAIL

Switches the displayed screen to the DETAIL screen.

This hard key is “7” in keypad mode.

SLOT

◄

Switches the module to control. Each time you press this hard key, you switch the

module that is being controlled to the module in the previous slot. This hard key is “8”

in keypad mode.

SLOT

►

Switches the module to control. Each time you press this hard key, you switch the

module that is being controlled to the module in the next slot. This hard key is “9” in

keypad mode.

SUMMARY

Switches the displayed screen to the SUMMARY screen.

This hard key is “4” in keypad mode.

HOLD

Stops updating the screen display. If you press this hard key again or if you press

another hard key, the screen display will start updating again.

This hard key is “5” in keypad mode.

APPLI

Displays the APPLICATION screen. This hard key is “6” in keypad mode.

FILE

Displays the FILE LIST screen. This hard key is “1” in keypad mode.

MACRO

Displays the MACRO screen. This hard key is “2” in keypad mode.

SYSTEM

Displays the SYSTEM screen. This hard key is “3” in keypad mode.

PRTSC

Saves a capture of the displayed screen to a file. This hard key is “0” in keypad

mode.

PRESET

Initializes the parameters of the frame and the installed modules.

This hard key is “.” in keypad mode.

SHIFT

Extension key. This hard key is “-” in keypad mode.

1.1 Frame Controller

1-3

IM 735101-01EN

Component Names and Functions

Index

Summary of Contents for AQ2200 Series
























































































































































































Search results

Summary of Contents for AQ2200 Series

Reviews:

Related manuals for AQ2200 Series

Brands by name

Popular brands

YOKOGAWA AQ2200 Series, User Manual

Search results

Summary of Contents for AQ2200 Series

Reviews:

Related manuals for AQ2200 Series

Brands by name

Popular brands