Yealink SIP-21P E2 User Manual Download Page 95

Page: 95 / 156

Basic Call Features

Depending on your selection:

a.) If you select Always Forward:

1) Press or , or the Switch soft key to select Enabled from the Always

Forward field.

2) Enter the destination number you want to forward all incoming calls to in

the Forward to field.

3) (Optional.) Enter the always forward on code or off code respectively in the

On Code or Off Code field.

b.) If you select Busy Forward:

1) Press or , or the Switch soft key to select Enabled from the Busy

Forward field.

2) Enter the destination number you want to forward incoming calls to when

the phone is busy in the Forward to field.

3) (Optional.) Enter the busy forward on code or off code respectively in the

On Code or Off Code field.

c.) If you select No Answer Forward:

1) Press or , or the Switch soft key to select Enabled from the No

Answer Forward field.

2) Enter the destination number you want to forward unanswered incoming

calls to in the Forward to field.

3) Press or , or the Switch soft key to select the ring time to wait

Summary of Contents for SIP-21P E2





























































































































































Search results

Summary of Contents for SIP-21P E2

Reviews:

Related manuals for SIP-21P E2

Brands by name

Popular brands

Yealink SIP-21P E2, User Manual

Search results

Summary of Contents for SIP-21P E2

Reviews:

Related manuals for SIP-21P E2

Brands by name

Popular brands