Yealink SIP-21P E2 User Manual Download Page 96

Page: 96 / 156

User Guide for the SIP-T21(P) E2 IP Phone

before forwarding from the After Ring Time field.

The default ring time is 12 seconds.

4) (Optional.) Enter the no answer forward on code or off code respectively in

the On Code or Off Code field.

Press the Save soft key to accept the change or the Back soft key to cancel.

The icon on the status bar indicates that the call forward is enabled.

To enable call forward in custom mode:

Press Menu->Features->Call Forward.

Press or to select the desired account, and then press the Enter soft key.

Press or to select the desired forwarding type, and then press the Enter

soft key.

Depending on your selection:

a.) If you select Always Forward, you can enable it for a specific account.

1) Press or , or the Switch soft key to select Enabled from the Always

Forward field.

2) Enter the destination number you want to forward all incoming calls to in

the Forward to field.

3) (Optional.) Enter the always forward on code or off code respectively in the

On Code or Off Code field.

You can also enable always forward for all accounts. After always forward was
enabled for a specific account, do the following:

1) Press or to highlight the Always Forward field.

2) Press the All Lines soft key.

Summary of Contents for SIP-21P E2





























































































































































Search results

Summary of Contents for SIP-21P E2

Reviews:

Related manuals for SIP-21P E2

Brands by name

Popular brands

Yealink SIP-21P E2, User Manual

Search results

Summary of Contents for SIP-21P E2

Reviews:

Related manuals for SIP-21P E2

Brands by name

Popular brands