Yealink SIP-21P E2 User Manual Download Page 128 | Manualshive

Page: 128 / 156

background image

User Guide for the SIP-T21(P) E2 IP Phone

118

To configure a default codec for multicast paging via web user interface:

1.

Click on Features->General Information.

2.

Select the desired codec from the pull-down list of Multicast Codec.

The default codec is G722.

3.

Click Confirm to accept the change.

Note

You can configure the phone to receive a Real Time Transport Protocol (RTP) stream from
the pre-configured multicast address(es) without involving SIP signaling. You can
specify up to 10 multicast addresses that the phone listens to on the network.

How the phone handles incoming multicast paging calls depends on Paging Barge and
Paging Priority Active parameters configured via web user interface.

Paging Barge

The paging barge parameter defines the priority of the voice call in progress. If the
priority of an incoming multicast paging call is lower than that of the active call, it will be
ignored automatically. If Disabled is selected from the pull-down list of Paging Barge,
the voice call in progress will take precedence over all incoming multicast paging calls.
Valid values in the Paging Barge field:

If G722 codec is used for multicast paging, the LCD screen will display the

icon to

indicate that it is providing high definition voice.

Default codec for multicast paging is configurable via web user interface only.

«
...
126
127
128
129
130
...
»

Summary of Contents for SIP-21P E2





























































































































































Reviews:

No comments

Related manuals for SIP-21P E2

Brand: Aastra Pages: 19

Clearspan 6757i

Brand: Aastra Pages: 2

Brand: Aastra Pages: 36

Brand: Aastra Pages: 56

Brand: Aastra Pages: 80

Brand: United Security Products Pages: 24

Brand: HTC Pages: 12

Brand: E-TEN Pages: 30

Brand: Hanlong Pages: 60

Brand: AEI COMMUNICATIONS Pages: 5

Brand: Snom Pages: 2

Brand: Audiovox Pages: 44

Brand: Teldat Pages: 165

Brand: ALIGATOR Pages: 13

Brand: Samsung Pages: 183

Brand: Samsung Pages: 102

Brand: Samsung Pages: 128

Brand: Samsung Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands