Yamaha T135S Service Manual Download Page 44

Page: 44 / 349

YamahaT135.COM

SPEC

2-22

CABLE ROUTING

Turn signal light relay

Meter assembly

Left handlebar switch lead

Speedometer cable

Wireharness

Brake hose

Throttle cable

Front brake light switch lead

Install the turn signal relay
onto the bracket.

∫

Connect the left handlebar
switch lead coupler in front of
the handlebar left.

Pass through the choke cable
into the wireharness.

∂

Connect the couplers in front
of the handlebar left side.

Do not pass the brake hose
into the bracket.

Pass through into the wire
guide, follow the routing order.
Brake hose, throttle cable and
wireharness.

Hook the strap of the wirehar-
ness onto the bracket.

Pass through the brake hose
into the wire guide on the han-
dlebar bracket.

∫

∂

∆

A-A

B-B

4
5

5YP-F8197-E0_2_1 05.6.27 19:46 Page 22

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands