Yamaha T135S Service Manual Download Page 331

Page: 331 / 349

YamahaT135.COM

2. Voltage

Connect the pocket tester (DC 20 V) to the
meter assembly coupler (wire harness side)
as shown.

Positive tester probe

→

brown

Negative tester probe

→

ground

Set the main switch to “ON”.

Measure the voltage (DC 12 V) of brown
lead terminal

on the meter assembly cou-

pler (wire harness side).

Is the voltage within specification?

ELEC

8-39

SIGNALING SYSTEM

YES

Check the wiring
connections of the
entire signaling sys-
tem

YES

Replace the fuel
level gauge.

3. Fuel level gauge

Set the main switch to “ON”.

Move the float up

or down

Check that the fuel level gauge needle
moves to “F” or “E”.

NOTE:

Before reading the fuel level gauge, leave the
float in one position (either up or down) for at
least three minutes.

Does the fuel level gauge needle move
appropriately?

4. Wiring

Check the entire signaling system’s wiring.

5YP-F8197-E0_8_1 05.6.27 19:28 Page 39

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands