Yamaha T135S Service Manual Download Page 244

Page: 244 / 349

YamahaT135.COM

CHAS

REAR WHEEL AND BRAKE

7-14

EAS00570

ASSEMBLING THE BRAKE SHOE
PLATE

1. Install:

brake camshaft

brake shoe wear indicator

brake camshaft lever

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Install the brake camshaft so its punch mark

is positioned as shown.

b. Align the projection

on the brake shoe

wear indicator with the notch in the brake
camshaft.

c. Align the punch mark in the brake camshaft

with the mark on the brake camshaft lever.

d. Check that the brake shoes are properly

positioned.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS00571

INSTALLING THE REAR WHEEL

1. Lubricate:

spacer

collar

wheel axle

wheel bearings

rear brake camshaft

brake torque rod bolt

oil seal lips

2. Install:

brake torque rod (to brake shoe plate)

washer

cotter pin

3. Install:

washer

compression spring

brake rod

brake rod adjusting nut

NOTE:

Press down on the brake pedal to install the
brake rod.

Recommended lubricant

Lithium-soap-based grease

19 Nm (1.9 m·kg, 14 ft·lb)

7 Nm (0.7 m·kg, 5.0 ft·lb)

5YP-F8197-E0_7_1 05.6.27 19:29 Page 14

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands