Yamaha T135S Service Manual Download Page 70

Page: 70 / 349

YamahaT135.COM

CHK

ADJ

3-16

MEASURING THE COMPRESSION PRESSURE

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Set the main switch to “ON”.
b. With the throttle wide open and push the

“START” switch, then crank the engine until
the reading on the compression gauge sta-
bilizes.

To prevent sparking, ground the spark plug
lead before cranking the engine.

c. If the compression pressure is above the

maximum specification, check the cylinder
head, valve surfaces, and piston crown for
carbon deposits.
Carbon deposits

→

Eliminate.

d. If the compression pressure is below the

minimum specification, pour a teaspoonful
of engine oil into the spark plug bore and
measure again.
Refer to the following table.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Compression pressure

(with oil applied into the cylinder)

Reading

Diagnosis
Piston ring(s) wear

Higher than with-

or damage

→

out oil

Repair.
Piston, valves, cyl-

Same as without

inder head gasket

oil

or piston possibly
defective

→

Repair.

6. Install:

compression gauge

7. Measure:

compression pressure
Out of specification

→

Refer to steps (c)

and (d).

Compression gauge

90890-03081

Compression pressure
(at sea level)

Minimum

490 kPa (4.9 kg/cm

, 70 psi)/at 500 r/min

Standard

560 kPa (5.6 kg/cm

, 80 psi)/at 500 r/min

Maximum

630 kPa (6.3 kg/cm

, 90 psi)/at 500 r/min

5YP-F8197-E0_3_1 05.6.27 20:32 Page 16

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands