Yamaha T135S Service Manual Download Page 208

Page: 208 / 349

YamahaT135.COM

EAS00467

INSTALLING THE THERMOSTAT

1. Install:

thermostat

thermostat cover

bracket

NOTE:

Face the hole toward to the forward to install.

5-8

COOL

COOLING SYSTEM

FWD

10 Nm (1.0 m•kg, 7.2 ft•lb)

EAS00475

ASSEMBLING THE WATER PUMP

1. Install:

water pump seal

NOTE:

Install the water pump seal with the special
tools.

Push down.

2. Lubricate:

water pump seal

Mechanical seal installer

90890-04145

Middle driven shaft bearing driver

90890-04058

Recommended lubricant

Lithium soap base grease

3. Install:

impeller

plate

NOTE:

Align the slit in the impeller shaft with the slot
of the plate.

After installation, check that the impeller shaft
rotates smoothly.

10 Nm (1.0 m•kg, 7.2 ft•lb)

5YP-F8197-E0_5_1 05.6.27 19:34 Page 8

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands