Yamaha T135S Service Manual Download Page 255

Page: 255 / 349

YamahaT135.COM

CHAS

FRONT BRAKE

7-25

EAS00588

DISASSEMBLING THE FRONT BRAKE
MASTER CYLINDER

NOTE:

Before disassembling the front brake master
cylinder, drain the brake fluid from the entire
brake system.

1. Remove:

side cowlings (left and right)

front cowling
Refer to “REMOVING THE SIDE COWL-
INGS” and “REMOVING THE FRONT
COWLING” in chapter 3.

headlight assembly
Refer to “REMOVING THE HEADLIGHT
ASSEMBLY” in chapter 3.

2. Remove:

union bolt

copper washers

brake hose

NOTE:

To collect any remaining brake fluid, place a
container under the master cylinder and the end
of the brake hose.

3. Remove:

brake master cylinder assembly

4. Remove:

brake light switch

brake lever

5YP-F8197-E0_7_1 05.6.27 19:29 Page 25

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands