Yamaha T135S Service Manual Download Page 129

Page: 129 / 349

YamahaT135.COM

4-23

ENG

VALVES AND VALVE SPRINGS

EASF0025

REMOVING THE VALVES

NOTE:

Prior to remove the valves, remove the cylinder
head, camshaft and rocker arms.

The following procedure applies to all of the
valves and related components.

NOTE:

Before removing the internal parts of the cylin-
der head (e.g., valves, valve springs, valve
seats), make sure the valves properly seal.

1. Check:

valve sealing
Leakage at the valve seat

→

Check the

valve face, valve seat, and valve seat width.
Refer to “CHECKING THE VALVE SEATS”.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Pour a clean solvent

into the intake and

exhaust ports.

b. Check that the valves properly seal.

NOTE:

There should be no leakage at the valve seat

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

5YP-F8197-E0_4_1 05.6.27 19:32 Page 23

Yamaha T135 Service Manual

YamahaT135.COM

Summary of Contents for T135S






























































































































































































































































































































































Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands

Yamaha T135S, Service Manual

Search results

Summary of Contents for T135S

Reviews:

Related manuals for T135S

Brands by name

Popular brands