Yamaha T135S Service Manual Download Page 100 | Manualshive

Page: 100 / 349

background image

YamahaT135.COM

1

CHK

ADJ

3-46

EASF0017

CHECKING THE FUSE

c

C

To avoid a short circuit, always set the main
switch to “OFF” when checking or replacing
a fuse.

1. Open the seat and battery cover.

CHECKING THE FUSE

2. Remove:

9

fuse holder

1

3. Check:

9

fuse

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Connect the pocket tester to the fuse and

check the continuity.

NOTE:

Set the pocket tester selector to “

Ω ×

1”.

b. If the pocket tester indicates “

∞

”, replace

the fuse.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

4. Replace:

9

blown fuse

w

Never use a fuse with an amperage rating
other than that specified. Improvising or
using a fuse with the wrong amperage rating
may cause extensive damage to the electri-
cal system, cause the lighting and ignition
systems to malfunction and could possibly
cause a fire.

5. Install:

9

fuse holder

Pocket tester

90890-03112

5YP-F8197-E0_3_1 05.6.27 20:33 Page 46

Yamaha T135 Service Manual

YamahaT135.COM

«
...
98
99
100
101
102
...
»

Summary of Contents for T135S






























































































































































































































































































































































Reviews:

No comments

Related manuals for T135S

Brand: X-lite Pages: 6

Brand: Öhlins Pages: 2

Mechatronics 35007-01

Brand: Öhlins Pages: 4

McPherson Strut MIR 5H02

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 4

Rocky Mountain-EXP SB-1

Brand: Wolfman Pages: 7

Super Adventure 2016

Brand: KTM Pages: 25

990D0-44G00-ALM

Brand: Suzuki Pages: 24

Brand: LAZER Pages: 11

Brand: Yoshimura Pages: 4

Brand: Malaguti Pages: 242

Brand: GAS GAS Pages: 131

Brand: Thunderbike Pages: 7

Brand: Fantic Motor Pages: 60

RACE 11621C0520

Brand: Yoshimura Pages: 7

Brand: AGV Pages: 64

Brand: Yamaha Pages: 390

Brand: Yamaha Pages: 468

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands